How to Calibrate a pH Pen

pH pen calibration tools

pH pens are a valuable tool for every grower. Maintaining a proper pH balance will prevent you from running into a lot of problems down the road. Cannabis roots can only absorb nutrients when the medium they’re in has a pH in the right window. If the pH is too low or high, your plant will show signs of a nutrient deficiency. The best way to maintain this balance is to measure the pH of every liquid you give your plants. This is where the pH pen is very handy.
pH pens can lose their accuracy over time, so it’s best to calibrate them every few months to make sure they are working correctly.
The pH pen we have available in the store is cheap and easy to calibrate. It also comes with some powder packets to make a buffer solution to calibrate the pen.

What is a “Buffer Solution”?

A buffer solution is a liquid that has a very stable pH. Adding an acid or base to it will have little effect. A buffer solution is sometimes called a calibration solution, they are used to calibrate pH sensors. These solutions can be found at hydroponic stores and usually come in pairs. The ones I use in this example have a pH of 4 and 7. You need two solutions so you can test them against each other. If you only calibrate to one, it’s impossible to guarantee accuracy.

Tools Required to Calibrate Your pH Pen

pH pen with calibration screw driver
pH buffer solution
Beer (optional)

Step By Step For Calibrating Your pH Pen

Step One – Calibrate to pH 4 Solution

Fill a small container with your buffer solution. You won’t need much, just enough to cover the sensor on the pen. In my case, I used a shot glass and filled it 3/4 of the way with the pH 4 buffer solution.
Next, put your pen in the solution and see what the reading is on the LCD screen. My pen was quite off and registered 2.8.
On the back of the pen, there is a small hole with a tiny screw inside. While keeping your pen in the buffer solution, use the small screwdriver to adjust the screw inside. You will need to turn it clockwise or counterclockwise until the LCD is reading 4.0

Incorrect pH reading
Incorrect pH reading
Calibrating a pH pen
Using the small screwdriver to calibrate the pen.
pH pen adjusted to pH of 4
pH pen adjusted to pH of 4

Step Two – Calibrate to pH 7 Solution

Rinse your pen off with some water, and do the same process with a clean shot glass and the pH 7 buffer solution. When you test it, it should read 7. If it doesn’t say 7 your pen might be no longer working properly.

These types of pH pens are very simple because they are calibrated manually. But, If they aren’t stored correctly they may lose their ability to correctly measure pH. Make sure to rinse off your pen after every use, shake it dry, and replace the cap. Store it in a safe dry place.

pH pen calibrated in pH 7 buffer solution
pH pen calibrated in pH 7 buffer solution

Step Three – Give It a Test

Now let’s have some fun with our calibrated pen and make sure it’s working correctly. I decided to test it out on some tap water and some Old Style Pilsner. The pH of my tap water is usually a little basic around 7.2 or 7.5. When I measured mine today it was 7.4
Beer, especially a lager or pilsner, has a pH that ranges between 4.2 and 4.6. When I measured my beer it was 4.4
Coca-Cola has a pH between 2.2 and 2.5. There are also many minerals waters with their pH listed on the label.

It looks like the pen is now calibrated properly. I will calibrate it again in about a month.

pH pen calibrated in pH 7 buffer solution
pH pen calibrated in pH 7 buffer solution

What Does ATC Stand For?

You’ll notice the pH pen has the letters ATC printed on it. ATC stands for Automatic Temperature Compensation. pH pens without ATC are less accurate.  The pH value will change depending on temperature. A pH pen with ATC will compensate for small differences in temperature. It’s a good idea to have all the solutions you’re measuring at the same temperature to maintain accuracy.

We have these pH pens available through the store. I personally like these ones because they are so easy to calibrate and store. Have you used these ones before? Let us know in the comments below.

Thanks for reading this article. If you found it helpful please share it with anyone else who might find it useful. If you have any question, please leave a comment below.

If you want to learn even more about growing cannabis, we offer a free 40+ page guide full of images. Get your today!

Grow Cannabis Guide

This guide will answer many questions about growing cannabis, like the following…

Selecting Seeds
Identify and Correct Problems
Maximize Yield
Much More…

Facebook Comments

4 thoughts on “How to Calibrate a pH Pen

  1. Pingback: Care Tips For Indoor Cannabis - Reefertilizer

Leave a Reply

Your email address will not be published. Required fields are marked *